Course Resources

See below for a full listing of downloadable course content.

Lab Lecture Topics Lecture Resources Lab Topics Lab Resources Homework
1
  • Course overview
  • AutoCAD Chapter 1: AutoCAD Fundamentals
  • Page 1-2 to 1-18
  • AutoCAD Chapter 1: AutoCAD Fundamentals – Guide Plate
  • Page 1-19 to 1-26
  • 1) Spacer Design (Pg 1-27 to 1-36)
  • 2) Ex 4 Channel Plate (Pg 1-39)
2
  • AutoCAD Chapter 2: Basic Object Construction Tools
  • Rocker Arm Design
  • Page 2-3 to 2-28
  • AutoCAD Chapter 2: Basic Object Construction Tools – Ex. 1 & 2
  • 1) Ex. 1 Adjustable Support
  • 2) Ex 2 V-Slide Plate
  • Page 2-30
3
  • AutoCAD Chapter 3: Geometric Construction and Editing Tools
  • Ex. 2 Interlacement Design
  • Page 3-3 to 3-20
  • AutoCAD Chapter 3: Gasket Design
  • Pages 3-21 to 3-39
  • 1) Ex 3 Positioning Spacer (Pg 3-42)
  • 2) Ex 4 Indexing Base (Pg 3-42)
4
  • AutoCAD Chapter 4: Object Properties and Organization
  • Floorplan Design
  • Page 4-3 to 4-28
  • Work on your midterm project
  • Midterm project (due Friday 10/23/2015 by 8 pm to Bblearn)
5
  • Creo Chapter 2 & 3: Introduction & Sketcher
  • Pages 17 to 47
  • Sketcher Practice
  • Pages 47 to 57
  • Creo Chapter 3: Sketcher Exercise
  • Sketcher Exercise Figure 3-69
  • Pages 58 to 67
  • Problem 3.5 Rocker (Pg 71)
6
  • Creo Chapters 4: Extrusions
  • Pipe Support Jig
  • Pages 75 to 92
  • Creo Chapter 4: Extrusions Exercise
  • Stocktail Clamp 197
  • Pages 92 to 104
  • 1) 4.2 Operating Arm (Pg 105)
  • 2) 4.6 Cross-feed Stop (Pg 107)
7
  • Creo Chapter 5: Revolves
  • Stepshaft
  • Pages 115 to 137
  • Creo Chapter 5: Revolves Exercise
  • Cone Clutch
  • Pages 137 to 147
  • 1) 5.1 Step Pulley (Pg 149)
  • 2) 5.5 Idler Pulley (Pg 151)
8
  • Creo Chapter 6: Patterns
  • 1) Erector Set Plate
  • 2) Saw Blade
  • Pages 155 to 177
  • Creo Chapter 6: Patterns Exercise
  • Dual-Tooth Sprocket
  • Pages 178 to 190
  • 1) Final Project Proposal
  • 2) 6.4 Bearing Cup (Pg 193)
  • 3) 6.6 Shelf Support (Pg 194)
9
  • Creo Chapter 9: Assemblies
  • Example Assembly
  • Pages 287 to 302
  • 1) Project Proposal Review
  • 2) Creo Chapter 9: Assembly Exercises
  • Take-Up Piece Assembly Figure 9-92
  • Pages 307 to 332
  • Completed Take-up Assembly Figure 9-103
  • Page 322 to 332
10
  • Creo Chapters 7: Creating an A-size Format Sheet
  • Creo Chapters 7 & 8: Engineering Drawings
  • Ch 7: Pages 197 to 218, 222 to 238
  • Ch 8: Pages 252 to 259
  • Creo Chapter 10: Assembly Drawings
  • Pages 343 to 352
  • Work on Final project
  • Final project due by Wednesday of Finals Week (12/09/2015) at 5pm to BbLearn
11
  • Finals week (Week 12)
  • Final project due by Wednesday of Finals Week (12/09/2015) at 5pm to BbLearn